ClipIt Prybars are here!  <------------And..the're gone!   But worry not more are on the way!

These measure 4.5" X 1/2" X 1/4" are made from A2 tool steel and tempered to about 57 HRC for toughness with a tumbled from heat treat finish which gives a cool random variation in color. Featuring a heat treated stainless pocket clip and a through hole for a lanyard. Get them while they last.

And if you are wondering how tough they are:

 I figured I would test one out so I proceeded to pound the crap out of it with a 2lb sledge. First I drove it through a 2 x 4 along the grain and split a few big chunks off, easy. So I decided to drive it cross grain. A little more pounding but it just laughed at me and went right on in. Ok fine. Then I found some old concrete cinder block around the house and made baby concrete chunks with my prybar as I pounded it right on through bit by bit. Very not bad! The tip ended up with a few scratches and MINOR dings. Then I figured what the hell and drove it into a post and put all of my 215lb ass up on it. My entire mass held up by this little 1/2" wide 1/4" thick piece of metal, it was impressive, I was happy. Unfortunately I was not able to get a pic of me standing on it, kinda hard to do by myself.
   So rest assured These will get the job done for you and then some. This is a limited run, all hand ground and machined by me so there are some slight variations. But that's what makes them hand made and awesome right?
 
While they last these are $old shipped to conUS and add $10 for international shipping please. Email me zwood45@gmail.com or PM me on facebook for purchase. www.facebook.com/zachwoodknives

Thanks for supporting Zach Wood Knives!

TiBars! $OLD Thank you everybody.

Mini TiBars are here! These are Titanium and roughly 3" X 1/2" X .180" and the longer ones (6,7,8) are 3-3/4". Awesome little buggers that You wont want to put down, true story. The first set 1-6 are sand blasted and heat anodized 1 and 2 have a slight bend like a nail bar. Numbers 7-11 are sand blasted heat anodized and tumbled number 10 & 11 have the slight bend too. 12-15 have an orangepeel finish and heat anodized and the last batch just has the orangepeel finish and left uncolored. These are $45 shipped to conUS, international pays shipping and assumes risk. Thanks for looking!

Some closer looks

Orangepeel

Orangepeel anodized

Sandblasted anodized

sandblasted anodized tumbled

Got a few things up today. All of these are one offs non production pieces

All 4 sides of one of my small brass beads measures 7/16 square with 3/16 through hole.$30 shipped (CON.US)

These are pure copper beads (2). Antiqued, 1/4" through hole, hand carved/ground. The one with "X" on it has 4 different sides(sold) the one on the right has the same pattern all the way around. They measure 1/2" square and 11/16" tall for the first and 3/4" tall for the right one. $OLD shipped. (CON.US)

Ok this one is another small 7/16" square brass. It has a cross hatch pattern on all sides with an antiqued/ forced patina finish. $OLD shipped. (CON.US)

This is a rough textured simple small bead. 3/16" through hole 7/16" square. $20 shipped (CON.US)

This is a really cool "Artifact" (watch for more Artifacts in the future) Prytool. Heat treated and blued high carbon steel. Wedge on top, bottle cap lifter and wedge/pry foot on bottom. $OLD shipped. (CON.US)

One of the very first run of my prytools. This one is heat treated, random etched and highlight polished high carbon steel. It is just like my Stainless ones but bigger measuring 3/4" wide and just over 3-3/4" long. Has 1/4" hex drive hole, bottle cap lifter, key ring hole and prying wedge. $38 shipped. (CON.US)


Please email me if you are interested in any of these or have any questions. Check back for updates and new stuff Thanks for looking!

zwood45@gmail.com
www.zwoodknives.com
www.facebook.com/z.knives/